User contributions
Jump to navigation
Jump to search
- 18:15, 22 March 2012 diff hist +66 FTDI ATmega →Related projects
- 18:14, 22 March 2012 diff hist +3 Temperature control →writing the software
- 14:00, 21 March 2012 diff hist -110 FTDI ATmega →Jumper settings
- 15:42, 19 March 2012 diff hist +656 Relay
- 14:49, 19 March 2012 diff hist +24 3FETs →Pinout
- 15:58, 12 March 2012 diff hist +37 Default addresses
- 15:55, 12 March 2012 diff hist +20 Default addresses
- 15:55, 12 March 2012 diff hist +70 N Default addresses Created page with "SPI_LCD 0x82 SPI_DIO 0x84 SPI_SERVO 0x86 SPI_7FETs 0x88 SPI_3FETs 0x8A"
- 15:49, 12 March 2012 diff hist +25 Main Page →Expansion boards
- 15:48, 12 March 2012 diff hist +2,474 N 3FETs Created page with "This is the documentation page for the SPI_3FETs board. == Overview == The board has 3 fets that allow you to pull a pin of a load low. You would normally tie the other end..."
- 15:44, 12 March 2012 diff hist +16 Main Page →Expansion boards
- 14:26, 12 March 2012 diff hist +1 RGB clock →Mode 2
- 14:25, 12 March 2012 diff hist -120 RGB clock →Jumper settings
- 13:57, 12 March 2012 diff hist -6 RGB clock →Adjusting the white-balance
- 13:55, 12 March 2012 diff hist +228 RGB clock →The software
- 13:48, 12 March 2012 diff hist +12 RGB clock →Using the pushbuttons
- 13:45, 12 March 2012 diff hist 0 m RGB clock →Reading back the time
- 11:25, 10 March 2012 diff hist +4 Modifying the arduino IDE for 20MHz current
- 11:18, 8 March 2012 diff hist -40 7FETs
- 20:41, 7 March 2012 diff hist +23 USB-multio →Additional software
- 20:40, 7 March 2012 diff hist +7 Usbio kitt →usbio Kitt
- 20:39, 7 March 2012 diff hist +5 Usbio ACM sample program →download
- 20:37, 7 March 2012 diff hist +9 RGB clock →The software
- 18:54, 2 March 2012 diff hist 0 7FETs
- 18:18, 2 March 2012 diff hist -1 FTDI ATmega →Linux
- 18:18, 2 March 2012 diff hist +306 FTDI ATmega →Linux
- 18:00, 2 March 2012 diff hist +20 SPI LCD →Jumper settings
- 15:14, 28 February 2012 diff hist +27 Main Page →Miscellaneous
- 15:13, 23 February 2012 diff hist -300 m FTDI ATmega Reverted edits by AngelicaByrd (Talk) to last revision by Tom
- 18:51, 22 February 2012 diff hist +92 FTDI serial →Changelog
- 18:49, 22 February 2012 diff hist +18 Main Page →Breakout boards
- 18:49, 22 February 2012 diff hist -18 Main Page →Other boards
- 18:45, 22 February 2012 diff hist +2 FTDI ATmega →Future hardware enhancements
- 18:02, 22 February 2012 diff hist -23 FTDI serial
- 01:03, 21 February 2012 diff hist +52 Windows →UNDER CONSTRUCTION current
- 01:02, 21 February 2012 diff hist +1,299 N Windows Created page with '= UNDER CONSTRUCTION = At the moment, this page is still heavily under construction. You can check one of the following howtos in the meantime: [http://www.atmel.com/microsite/av…'
- 00:11, 21 February 2012 diff hist +69 Main Page
- 17:47, 17 February 2012 diff hist 0 Servo →1.2
- 17:47, 17 February 2012 diff hist +72 Servo →Changelog
- 17:46, 17 February 2012 diff hist -99 Servo →Future hardware enhancements
- 17:20, 17 February 2012 diff hist +375 Servo →Overview
- 17:17, 17 February 2012 diff hist +12 Servo →Jumper settings
- 17:17, 17 February 2012 diff hist +53 Servo
- 20:48, 15 February 2012 diff hist +202 RGB clock →The software
- 20:14, 15 February 2012 diff hist +1,851 N Servo 1.0 protocol Created page with 'The addresses on the SPI bus are 7 bits wide. The lower bit specifies if the transaction is to be a read or a write. Write transactions have the lower bit cleared (0), read trans…'
- 19:09, 15 February 2012 diff hist +207 Servo
- 19:06, 15 February 2012 diff hist 0 SPI LCD →External resources
- 19:01, 15 February 2012 diff hist +1,132 Servo
- 16:33, 15 February 2012 diff hist 0 7FETs
- 16:33, 15 February 2012 diff hist 0 Main Page