LCD

From BitWizard WIKI
Revision as of 10:01, 14 August 2012 by Rew (talk | contribs) (The software)

Jump to: navigation, search
The SPI_LCD board
The SPI_LCD board

This is the documentation page for the SPI_LCD and I2C_LCD boards.

Overview

Assembly instructions

The board comes fully assembled, as depicted in the picture on the top right of this page..

We assemble the ones with LCD with just a pin header between the board and the LCD, so you could do the same. Make sure you put the LCD in correctly. I'm not sure everything survives the wrong polarity.

Recommended configuration
Recommended configuration
Also possible
Also possible
Not recommended configuration
Not recommended configuration


Possible Configurations

For the SPI version the second SPI port can be used as an ICSP connector. You need to toggle the solder jumper for this. The I2C or SPI bus cannot be left connected during programming.

External resources

Datasheets

The fet: http://www.irf.com/product-info/datasheets/data/irlml2244pbf.pdf

The CPU: http://www.atmel.com/dyn/resources/prod_documents/doc8006.pdf

Additional software

For the I2c version there is a demo project for arduino at http://www.bitwizard.nl/software/ar_i2c_lcd_demo.pde


For the SPI version there is a demo project for arduino at http://www.bitwizard.nl/software/ardemo_lcd.pde


For use with a raspberry pi there are a few options. For the I2C version, you can get http://www.bitwizard.nl/software/bw_rpi_tools-20120616.tgz . The GPIO directory in that archive contains some programs to communicate with the LCD with a userspace driver. There is also a kernel-space driver for the I2C module, but I haven't looked at accessing that from userspace yet. (the kernel-space driver will allow other kernel drivers, for example for a temperature sensor, to access the I2C bus).

For SPI on the raspberry pi, the same gpio directory contains "send_spi". It will allow you to send stuff to the SPI display.

For SPI there is also a beta kernel driver. That is what the other directory bw_spi is for.

Related projects

Pinout

For the SPI connector see: SPI_connector_pinout.
For the I2C connector see: I2C_connector_pinout.


LEDs

The only LED is a power indicator.

Jumper settings

There are two solder jumpers. The one between the two 6-pin SPI connectors controls the function of the SPI connector furthest from the CPU.

In the default configuration the second SPI connector is a daisy-chain connector for the SPI bus.
In the other configuration, the second SPI connector is the ICSP connector.

There is a 10 mil (very small) PCB trace in the solder jumper in the default configuration. You'll have to cut this trace to move the solderjumper to the other position. If you later decide you want the other configuration again, some solder-wick can be used to remove the solder from one position and then it can be added to the other position.

Programming

For the intro to the SPI and I2C protocols read: SPI versus I2C protocols

The board specific protocol can be found here: spi_lcd 1.3_protocol spi_lcd_1.2_protocol i2c_lcd_protocol

You should also read the General_SPI_protocol notes.

For arduino, a sample PDE is available, called ardemo_lcd.pde, also at BitWizard software download directory .

This is a demo to send things using SPI to the lcd board. The SPI routines there are applicable for LCD boards as well.

The software

If you are going to connect your I2C_LCD or SPI_LCD to a raspbery pi, read: getting started with rpi_serial and BitWizard expansion boards

Future hardware enhancements

hardware potentiometer for the contrast. (option).

Future software enhancements

  • Lock the address. (require a sequence of commands to change the address).

Changelog

1.2

  • Initial public release