Raspduino

From BitWizard WIKI
Revision as of 00:53, 14 December 2012 by David (talk | contribs) (Raspberry Pi connectors)

Jump to: navigation, search
The Raspduino V1.1
The Raspduino V1.1

This is the documentation page for the BitWizard Raspduino board. The Raspduino is an Arduino compatible microcontroller board, designed to plug on top of a Raspberry Pi (some people like to call this Pi Plates). It is then possible to add Arduino shields to the Raspduino.

The Raspduino can be bought in the BitWizard shop.

Features

  • Fully Arduino compatible
  • Plugs directly on a Raspberry Pi
  • Compatible with (almost) all Arduino shields
  • Equipped with an ATmega328 microcontroller
  • Upto 8 analog inputs
  • Upto 20 digital I/O
  • Breaks out the Raspberry Pi's SPI and I2C busses

Connectors and pinout

The Raspduino of course has the same connectors and pinout as a regular Arduino, and some extra connectors.

Raspberry Pi connectors

The Raspberry Pi has two SPI busses, and one I2C bus. Those are (just like on our Raspberry_Pi_Serial board) broken out to their respective headers, labeled as SPI0, SPI1, and I2C. The signals on these busses are 3V3, but the inputs are 5V tolerant. With the 3V3/5V jumper, you can control what supply voltage is delivered to these connectors. The default setting is 5V.

Power input

It is possible to connect an external power supply on these pins, in case you want to use your Raspduino without a Raspberry Pi.

Extra analog connector

The RaspDuino has two extra analog pins (A6 and A7) provided on an extra connector located near the analog pins. The connector also provides ground and 5V (or optionally 3V3).

LEDs

The Raspduino has two LEDs: A power indicator, and a LED connected to digital pin 13.

Jumpers

The raspduino has a number of jumpers, to configure it for multiple different scenarios.

ICSP/SPI jumper

It is possible to use this connector as an ICSP connector for the AVR, or an SPI connector. By default, this connector is configured as an ICSP connector, but by cutting the trace between the ICSP pad and the center pad, and shorting the center pad to the SPI pad, this connector can be used as an SPI connector. For example to connect one of the the BitWizard SPI expansion boards from the Raspduino.

I2C jumpers

It is possible to connect the Raspberry Pi's I2C bus to the I2C bus of the AVR. To do this, you need to short the SCL and SDA jumpers with a solder bridge.

Serial busses voltage selection jumper

The 3V3/5V jumper next to the Raspberry Pi connector controls the voltage supplied to the connectors that break out the Raspberry Pi's SPI and I2C busses. It is possible to run these busses on 5V or 3V3. 5V Is the default setting, but by cutting the trace between the 5V pad and the center pad, and connecting the 3V3 pad to the center pad with a solder bridge, you can set the supply voltage to 3V3.

AVR voltage selection jumper

It is possible to run the AVR on 5V or 3V3 when the Raspduino is connected to a Raspberry Pi. The default setting is 5V. To set the AVR voltage to 3V3, cut the trace between the 5V pad and the center pad, and connecting the 3V3 pad to the center pad with a solder bridge. It might be necessary to run the ATMega at 8MHz when it's running on 3V3.

Powering the Raspduino

You can power the Raspduino in two different ways; By the Raspberry Pi it is plugged into, or if it is used stand-alone, you can connect an external power supply to the "External Power" connector. The supply voltage should be between 7 and 15V. If the voltage is higher than 5V, it will be regulated down to 5V.

Uploading a sketch

Future hardware enhancements

Suggestions are welcome.

Changelog

1.1

  • Initial public release