Search results

• FT2232H breakout board
  <tr><td>GND</td><td>1</td><td>2</td><td>VCC</td></tr> * 1-2 3.3V
  2 KB (303 words) - 18:20, 26 July 2023
• PiPower
  JP1: 2-3<br> JP1: 1-2<br>
  4 KB (686 words) - 14:55, 17 July 2012
• USB Relay
  | 2 || C 1 || center connection for relay 1 | 4 || NO 2 || Normally open contact for relay 2
  4 KB (570 words) - 13:15, 11 November 2015
• Blog 26
  sprintf(bufline2, "1=down |2=up |5=res", bufline2); if (Button == 2){
  4 KB (517 words) - 12:55, 9 February 2016
• Dio breakout
  | 2 || IO0 | 2 || VCC
  2 KB (268 words) - 14:06, 10 December 2015
• FTDI serial
  <tr><td>2</td><td>Rx (R)</td><td>do not drive at 5V level if jumper is set to 3.3v.<b 1-2: 3V3 (jumper on the side nearest the chip and USB connector)<br>
  2 KB (333 words) - 17:53, 6 November 2015
• Uart connector pinout
  | 2 || RXD || recieve Data (input) | 2 || RXD || D1 || TXD on the arduino
  1 KB (205 words) - 14:11, 1 June 2012
• Servo
  | 2 || VCC || 5V | 2 || VCC || 5V
  4 KB (723 words) - 13:57, 2 November 2015
• FT4222h
  On the I2C connector you can find the I2C signals SDA (pin 2) and SCL (pin 3) as well as GND (pin 1) and VCC (pin 4). There is no pullu * 2 - GND
  3 KB (625 words) - 21:12, 17 November 2020
• Raspberry Relay
  ! Pin 1 !! Pin 2 !! Pin 3 !! Pin 4 !! Pin 5 !! Pin 6 !! Pin 7 !! Pin 8 !! Pin 9 !! Pin 10 | Neutral || Relay 1 out || Neutral || Relay 2 out || Neutral || Relay 3 out || Neutral || Relay 4 out || Neutral || Hot
  5 KB (891 words) - 17:31, 31 December 2021
• Blog 02
  ...or 3, 5 and 7) is where the (+)blue cable has to be putt in and other pin 2( or 4, 6, 8 ) I have to put the (-)brown cable. I want to protect the bottom protrusions, with 2 times tape on them so that they don't get trough it.
  3 KB (626 words) - 10:08, 22 September 2015
• Blog 18
  ...button 5(up) and 6(down). On the screen there will be visible which of the 2 menu you can go to. With button 1 and 2 you can choose which of the 2 you want to use.
  5 KB (774 words) - 15:53, 4 December 2015
• Thermocouple
  The jumper has: 1: GND, 2: DEV POWER, 3: 5V (from SPI). Put the jumper on 2-3 to use the SPI power (from the arduino? i.e. from USB? -> max at most 400
  3 KB (497 words) - 12:40, 10 May 2019
• Relay
  * 2 - 5V for the relays (marked "aux 5V") ...ecting the powersupply GND to pin 1 and the 5V from the powersupply to pin 2.
  6 KB (943 words) - 13:56, 2 November 2015
• USB-step
  2 - A+ ...the activation pattern. For forward use: 4 1 2 4 8, for reverse use "4 8 4 2 1" as the arguments.
  4 KB (560 words) - 18:00, 17 March 2016
• 7FETs
  | 2 || OUT0 || The jumper has: 1: GND, 2: DEV POWER, 3: 5V (from SPI).
  5 KB (770 words) - 18:10, 5 November 2015
• I2C magnetometer
  $mag -W 10:2:b z=`echo $result | awk '{print $3$2}'`
  1 KB (259 words) - 13:09, 11 November 2015
• Raspberry Pi LCD program
  Print the text "Hello World" on line 1, character 2: bw_lcd -T 2,1 "Hello World"
  2 KB (305 words) - 12:45, 11 November 2015
• Motor
  | 2 || Output B2 | <10V || No jumper, external 10V to 14V power source connected to pin 2
  4 KB (590 words) - 09:12, 9 September 2017
• I2C accellerometer
  $acc -W 0e:"$range":b 2b:2:b 2c:0:b 2d:1:b 2e:1:b 2a:39:b z=`echo $result | awk '{print $3$2}'`
  2 KB (310 words) - 13:09, 11 November 2015

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)