Difference between revisions of "USB-opto"
|Line 5:||Line 5:|
== overview ==
== overview ==
The USB-opto PCB has an USB connector and two
The USB-opto PCB has an USB connector and two -pin connectors. The brains of the PCB is an at90usb162 (or compatible) chip.
== pinout ==
== pinout ==
The 16 pin connectors
The 16 pin connectors connected as follows
Revision as of 15:58, 23 September 2011
This is the documentation page for the USB-opto PCB.
The USB-opto PCB has an USB connector and two 16-pin connectors. The brains of the PCB is an at90usb162 (or compatible) chip.
The 16 pin connectors are connected as follows
|1||Emitter opto 2A|
|2||Collector opto 2A|
|3||Emitter opto 1A|
|4||Collector opto 1A|
|5||Emitter opto 2B|
|6||Collector opto 2B|
|7||Emitter opto 1B|
|8||Collector opto 1B|
|9||Emitter opto 2C|
|10||Collector opto 2C|
|11||Emitter opto 1C|
|12||Collector opto 1C|
|13||Emitter opto 2D|
|14||Collector opto 2D|
|15||Emitter opto 1D|
|16||Collector opto 1D|
- led1 is connected to VCC
- led2 is connected to PD0
- led3 is connected to PC2
This section describes how you get your program into the processor.
In general what you need to know is that the processor will boot into the code you programmed into it on powerup. Once you're done developing your program, that's the way you'll use it: Powerup, run.
If there is no program loaded or if you press the reset button the chip comes up in "firmware upload mode". This is done by a bootloader. You should take care not to overwrite or erase the bootloader, because there is no way to put the bootloader back once it is gone.
Get the dfu-programmer for atmel chips package. (link?)
On sufficiently recent Ubunu distributions that is as simple as:
sudo apt-get install dfu-programmer
I recommend creating a script called "dfu":
#!/bin/sh if [ -z "$CHIP" ] ; then chip=at90usb162 else chip=$CHIP fi hex=$1 sudo dfu-programmer $chip erase sudo dfu-programmer $chip flash --suppress-bootloader-mem $hex sudo dfu-programmer $chip start
TODO: figure out how to get rid of the "sudo" commands here...
Now downloading and starting a program is as simple as pressing the reset button and then:
TODO: When I'm developing, I'm likely to modify the code, and when I want to program the chip I hit the "reset" button on the board. Then the computer will see my chip re-enumerate as the Atmel DFU chip. A simple script could watchout for that and invoke dfu <mycurrentbinary>.hex the moment the chip has enumerated. Once that's running downloading and starting the latest code becomes as simple as hitting the reset button.
Apparently the FLIP program is now available for Linux too. See below.
Get the "flip" program from Atmel. http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3886
The chip is an at90usb162. http://www.atmel.com/dyn/resources/prod_documents/doc7707.pdf
You can program the processor as if it is a normal AVR processor without USB. Just like an arduino. Or you can program it to have USB support. For this the LUFA package is very useful. http://www.fourwalledcubicle.com/LUFA.php
Depending on what you want you can start from these examples:
DONE: Find out if we can jump to the bootloader from our code so that we can issue a "go get yourself updated" command over the USB (yes, but the documentation says nothing about what address to jump to). This comes in handy if the reset button is difficult to reach because the device is built-in somewhere. http://www.atmel.com/dyn/resources/prod_documents/doc7618.pdf
future hardware enhancements
- Make an ICSP connector.
future software enhancements
- program the LUFA bootloader.
- Program an even smaller bootloader. (512 bytes should be possible, CF teensy/halfkay).