Search results
Create the page "$2" on this wiki! See also the search results found.
Page title matches
Page text matches
- | 2 || OUT1 ||4 KB (722 words) - 12:53, 11 November 2015
- ...ed 25 through 28. The other pins are numbered 1,3,5,...-23 on one side and 2,4,6,...-24 on the other side. <tr><td>1,2,7,8,10</td><td>GND</td></tr>1 KB (196 words) - 13:05, 11 November 2015
- | 0x32 || '2'3 KB (448 words) - 17:43, 4 July 2013
- | 2 || SDA || Serial I2C Data | 2 || SDA || A4 (Analog input 4) || Digital 20934 bytes (149 words) - 12:12, 10 December 2015
- This is the documentation page for the FTDI-serial 2 board. That you can buy in the [http://www.bitwizard.nl/shop/usb-boards/usb The FTDI-serial 2 board has an USB connector and a 4-pin serial/UART connector. The brains of964 bytes (151 words) - 17:53, 6 November 2015
- | 2 || Output B2 | <10V || No jumper, external 10V to 14V power source connected to pin 24 KB (590 words) - 09:12, 9 September 2017
- | 2 || RXD || recieve Data (input) | 2 || RXD || D1 || TXD on the arduino1 KB (205 words) - 14:11, 1 June 2012
- Print the text "Hello World" on line 1, character 2: bw_lcd -T 2,1 "Hello World"2 KB (305 words) - 12:45, 11 November 2015
- ...ed between 190 and 200mA, which translates to a power consumption of about 2,4W.3 KB (529 words) - 13:59, 18 August 2014
- JP1: 2-3<br> JP1: 1-2<br>4 KB (686 words) - 14:55, 17 July 2012
- * for the i2c version on a rev 2 raspberry pi, you need to specify the other I2C bus:1 KB (201 words) - 12:30, 4 January 2013
- ...: These scripts are written on a version 1 board. To run them on a version 2, change the I2C bus from "0" to "1".3 KB (450 words) - 12:43, 1 October 2012
- sleep 22 KB (366 words) - 18:01, 4 December 2015
- | 2 || Analog in The recommended configuration is to have 1-3 connected. The pins 1 and 2 are marked on the PCB. So 1-3 means the jumper is closest to the board edge12 KB (1,918 words) - 17:02, 14 January 2016
- ...ificant bit controls one of the dots. The lower dot is controlled by digit 2, and the upper dot by digit 3.3 KB (382 words) - 12:58, 11 November 2015
- | 0x21 || read button 2 (1 means NOT pushed, 0 means pushed) | 0x41 || read button 2 (1 means pushed, 0 means NOT pushed) (V1.1 and up)2 KB (328 words) - 12:59, 11 November 2015
- $ui -w 80:22 KB (267 words) - 15:48, 7 September 2015
- <tr><td>2</td><td>Analog6</td></tr>8 KB (1,268 words) - 15:14, 11 August 2016
- ...6-bit result, you need 6 more bits of resolution (n=6), so you need to add 2^12 (4096) samples together.6 KB (1,058 words) - 15:12, 9 December 2015
- | 0x09 || write up to 20 bytes for startupmessage line 2. || 1.6 and higher6 KB (972 words) - 16:46, 30 November 2015