Search results

Create the page "$2" on this wiki! See also the search results found.

Page title matches

• FTDI serial 2
  This is the documentation page for the FTDI-serial 2 board. That you can buy in the [http://www.bitwizard.nl/shop/usb-boards/usb The FTDI-serial 2 board has an USB connector and a 4-pin serial/UART connector. The brains of
  964 bytes (151 words) - 17:53, 6 November 2015
• Raspberry Pi User Interface with 16 x 2 LCD with a console serial cable
  687 bytes (130 words) - 13:34, 16 January 2013
• Raspberry Pi User Interface with 16 x 2 LCD
  #REDIRECT [[Raspberry Pi User Interface with 16 x 2 LCD with a console serial cable]]
  85 bytes (13 words) - 13:14, 16 January 2013
• Ftdi serial 2
  #REDIRECT [[FTDI serial 2]]
  27 bytes (3 words) - 11:07, 24 December 2015

Page text matches

• Main Page
  * [[FTDI serial 2]]
  4 KB (508 words) - 06:27, 14 June 2021
• Usbbigmultio
  <tr><td>2</td><td>GND</td></tr> <tr><td>2</td><td>GND</td></tr>
  6 KB (1,050 words) - 16:48, 21 December 2015
• FTDI ATmega
  <tr><td></td><td>3</td><td>2</td></tr> <li>Unlike a regular arduino, there are 2 onboard LED's, connected to pin A4 and A5. You can use those LED's with di
  6 KB (1,047 words) - 13:12, 2 November 2015
• USB-SATA powerswitch
  (sleep 0.2; echo set 0 ; sleep 0.2 ; echo set 1 ; sleep 0.2 ; echo set 2 ) > $tty ...output zero", which is the 12V output. "set 1" id the 5V output, and "set 2" is the 3V3 output. The four extra status LEDs are connected to output 3,4,
  7 KB (1,265 words) - 13:01, 11 November 2015
• USB-opto
  <tr><td>2</td><td>Collector opto 2A</td></tr> 2.0
  4 KB (690 words) - 13:03, 11 November 2015
• Cyclone dev board
  <tr><td>2</td><td>GND</td></tr> <tr><td>4</td><td>pin 2</td></tr>
  4 KB (818 words) - 14:23, 1 February 2012
• FT245RL breakout board
  <tr><td>2</td><td>GND</td></tr> 1-2: 3V3<br>
  1 KB (226 words) - 17:52, 6 November 2015
• FT2232H breakout board
  <tr><td>GND</td><td>1</td><td>2</td><td>VCC</td></tr> * 1-2 3.3V
  2 KB (303 words) - 18:20, 26 July 2023
• FTDI serial
  <tr><td>2</td><td>Rx (R)</td><td>do not drive at 5V level if jumper is set to 3.3v.<b 1-2: 3V3 (jumper on the side nearest the chip and USB connector)<br>
  2 KB (333 words) - 17:53, 6 November 2015
• RGB clock
  Qj 2 SV6 Qb 2 SV2
  15 KB (2,452 words) - 12:03, 2 December 2015
• USB-multio
  <tr><td>2</td><td>GND</td></tr> ==== Version 2.1 ====
  8 KB (1,331 words) - 16:16, 18 December 2015
• 7FETs
  | 2 || OUT0 || The jumper has: 1: GND, 2: DEV POWER, 3: 5V (from SPI).
  5 KB (770 words) - 18:10, 5 November 2015
• Servo
  | 2 || VCC || 5V | 2 || VCC || 5V
  4 KB (723 words) - 13:57, 2 November 2015
• Temperature Interface
  * 2 signal The sensors claim a +/- 1 or +/- 2 degree accuracy. But the system adds a few more uncertainties. For example,
  5 KB (734 words) - 12:54, 11 November 2015
• DIO
  | 2 || VCC
  2 KB (321 words) - 17:05, 9 December 2015
• Relay
  * 2 - 5V for the relays (marked "aux 5V") ...ecting the powersupply GND to pin 1 and the 5V from the powersupply to pin 2.
  6 KB (943 words) - 13:56, 2 November 2015
• 16 LEDs
  ...t the common-cathode version. This connects all the cathodes to GND (pin 1/2) and then all the inputs to the leds. This results in normal logic: the led To test the 16LED, connect the GND (pin 1 or 2) to any of the GND pins on your board.
  3 KB (445 words) - 12:59, 11 November 2015
• Spi lcd 1.3 protocol
  | 0x09 || Set startup message line 2.
  4 KB (642 words) - 16:34, 30 November 2015
• SPI connector pinout
  | 2 || VCC || power | 1 || 2
  2 KB (309 words) - 10:50, 10 March 2015
• DIO protocol
  !rowspan="2"|port !!colspan="4"|available on !!rowspan="2"|function | 0x70 .. 0x76 || v1.2 and up || || || || Select which i/o is coupled to which ADC channel. See
  16 KB (2,633 words) - 12:04, 19 May 2017

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)